Static aeroelastic program

Set of programs computes geometric, mass, aerodynamic, and structural effects on fighter and transport type aircraft at subsonic and supersonic speeds

Acoustic plane waves incident on an oblique clamped panel in a rectangular duct

The theory of acoustic plane waves incident on an oblique clamped panel in a rectangular duct was developed from basic theoretical concepts. The coupling theory between the elastic vibrations of the panel (plate) and the oblique incident acoustic plane wave in infinite space was considered in detail, and was used for the oblique clamped panel in the rectangular duct. The partial differential equation which governs the vibrations of the clamped panel (plate) was modified by adding to it stiffness (spring) forces and damping forces. The Transmission Loss coefficient and the Noise Reduction coefficient for oblique incidence were defined and derived in detail. The resonance frequencies excited by the free vibrations of the oblique finite clamped panel (plate) were derived and calculated in detail for the present case

Comparison of selected lift and sideslip characteristics of the Ayres Thrush S2R-800, winglets off and winglets on, to full-scale wind-tunnel data

All calculations were done in the stability axes system. The winglets used were constructed of modified GA(w)-2 airfoils. Aerodynamic characteristics discussed include: angle of attack; lift-curve slope; side force; yawing moments; rolling moments

Comparison of theoretically predicted lateral-directional aerodynamic characteristics with full-scale wind tunnel data on the ATLIT airplane

An analytical method is presented for predicting lateral-directional aerodynamic characteristics of light twin engine propeller-driven airplanes. This method is applied to the Advanced Technology Light Twin Engine airplane. The calculated characteristics are correlated against full-scale wind tunnel data. The method predicts the sideslip derivatives fairly well, although angle of attack variations are not well predicted. Spoiler performance was predicted somewhat high but was still reasonable. The rudder derivatives were not well predicted, in particular the effect of angle of attack. The predicted dynamic derivatives could not be correlated due to lack of experimental data

An investigation into the vertical axis control power requirements for landing VTOL type aircraft onboard nonaviation ships in various sea states

The problem of determining the vertical axis control requirements for landing a VTOL aircraft on a moving ship deck in various sea states is examined. Both a fixed-base piloted simulation and a nonpiloted simulation were used to determine the landing performance as influenced by thrust-to-weight ratio, vertical damping, and engine lags. The piloted simulation was run using a fixed-based simulator at Ames Research center. Simplified versions of an existing AV-8A Harrier model and an existing head-up display format were used. The ship model used was that of a DD963 class destroyer. Simplified linear models of the pilot, aircraft, ship motion, and ship air-wake turbulence were developed for the nonpiloted simulation. A unique aspect of the nonpiloted simulation was the development of a model of the piloting strategy used for shipboard landing. This model was refined during the piloted simulation until it provided a reasonably good representation of observed pilot behavior

A research program to reduce interior noise in general aviation airplanes: Noise reduction through a cavity-backed flexible plate

A prediction method is reported for noise reduction through a cavity-backed panel. The analysis takes into account only cavity modes in one direction. The results of this analysis were to find the effect of acoustic stiffness of a backing cavity on the panel behavior. The resulting changes in the noise reduction through the panel are significant

A research program to reduce the interior noise in general aviation aircraft, index and summary

This report is an index of the published works from NASA Grant NSG 1301, entitled A Research Program to Reduce the Interior Noise in General Aviation Aircraft. Included are a list of all published reports and papers, a compilation of test specimen characteristics, and summaries of each published work

Some comments on trim drag

A discussion of data of and methods for predicting trim drag is presented. Specifically the following subjects are discussed: (1) economic impact of trim drag; (2) the trim drag problem in propeller driven airplanes and the effect of propeller and nacelle location; (3) theoretical procedures for predicting trim drag; and (4) research needs in the area of trim drag

Determination of the static performance of a Cuyuna cc model UL-430RR engine

The results of static performance tests were carried out on an ultralight engine. A Cuyuna 430 cc, 2 stroke, 2 cylinder model was used to measure thrust, torque, propeller RPM, fuel flow, cylinder head temperature, and change in pressure through the propeller. Measurement of each of the above parameters was taken at specific values of RPM. The propeller's RPM's ranged from idle at approximately 750 RPM to a maximum value of 2810 RPM. The test results were then manipulated to obtain thrust coefficient, power coefficient, shaft horse power, and shaft specific fuel consumption

Measurement of transmission loss characteristics using acoustic intensity techniques at the KU-FRL Acoustic Test Facility

The transmission loss characteristics of panels using the acoustic intensity technique is presented. The theoretical formulation, installation of hardware, modifications to the test facility, and development of computer programs and test procedures are described. A listing of all the programs is also provided. The initial test results indicate that the acoustic intensity technique is easily adapted to measure transmission loss characteristics of panels. Use of this method will give average transmission loss values. The fixtures developed to position the microphones along the grid points are very useful in plotting the intensity maps of vibrating panels